Your Plumbing Crash Course: A Guide to Bathtub Installation
Your Plumbing Crash Course: A Guide to Bathtub Installation
Blog Article
What are your opinions about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?

Installing a bath tub isn't precisely brain surgery, however it does need strong plumbing, woodworking, as well as occasionally, tiling skills. Replacing an old tub with a new one is additionally a moderately tough task. If the old tub is easily easily accessible, the project can relocate quickly; if you have to open a wall to remove the old bathtub and position the brand-new bath tub, the job is a lot harder. In either situation, the task is within a house handyman's skills, although you will require a helper to move out the old tub and also embeded in the new one. See to it you have actually qualified on your own for the task and are comfortable attempting it. Instead of employing a specialist to take control of a halfway-completed task, it is far better to think about using one before you start. Possibilities are you might require a specialist plumber to make tube connections.
This write-up will certainly assist you install a new bath tub in your shower room if you have currently bought a new tub as well as don't require to transform the setup of your previous supply of water pipelines.
Your tools and also product list must comprise the following:
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your installation, then the first thing you need to do is separate the water. After doing so, turn on the faucets to drain any kind of water continuing to be in the system. The process of eliminating the existing taps can be quite problematic because of the restricted access that is often the instance.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipes to the taps. Have a towel prepared for the continuing to be water that will certainly originate from the pipes. As soon as the supply pipes have actually been gotten rid of, use the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from transforming during this process. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing substance.
Prior to going on to fit the new faucets, compare the pipeline connections on the old taps to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Touches
If the tails of the new taps are plastic, then you will need a plastic adapter to prevent damages to the thread. One end of the connector fits on the plastic tail of the tap and also the other end offers a link to the existent supply pipes.
If you need to fit a monobloc, then you will certainly call for decreasing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, place the faucet in the mounting hole in the bath/basin guaranteeing that the washers are in area in between the tap as well as the sink. Secure the faucet in position with the maker offered backnut. As soon as the faucet is safely in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical tap ports. The former kind must be linked to the faucet ends first, tightening up just by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been attached.
Setting up the Bath tub
Making use of both wooden boards under its feet, put the tub in the required setting. The wood boards are useful in equally spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto 4 little factors.
The following objective is to ensure that the tub is leveled all round. This can be accomplished by checking the level and also changing the feet on the bathtub till the level reads level.
To install taps, fit the bottom of the outermost versatile tap port to the suitable supply pipe by making a compression sign up with; after that do the exact same for the other tap.
Turn on the supply of water and also examine all joints as well as brand-new pipework for leakages as well as tighten them if necessary. Fill the bath tub as well as likewise examine the overflow electrical outlet and also the regular outlet for leaks.
Ultimately, deal with the bath paneling as described in the producer's instruction manual. Tiling as well as securing around the bathtub ought to wait until the tub has actually been used at the very least when as this will certainly settle it right into its last setting.
Planning for the Installment
To start with, the supporting frame provided with the bathroom must be fitted (if needed) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is essential to make certain that if the tap features a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the faucets device to avoid stress on the bathtub.
Fit the versatile faucet connectors to the bottom of the two taps utilizing 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet via the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you utilize every one of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath should currently be ready to be suited its last position.
Tiling Around the Bath tub
In the location where the bath meets the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the installation can relocate enough to fracture a rigid seal, triggering the water to penetrate the wall surface between the bathroom and also the tiling, causing issues with wetness and also feasible leakages to the ceiling below.
You can choose from a variety of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes and cartridges, and are capable of sealing voids as much as a size of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with spins of soaked newspaper or soft rope. Keep in mind to always fill the tub with water prior to securing, to permit the motion experienced when the tub is in use. The sealer can fracture relatively early if you do not consider this activity before securing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally easily available on the market. It is a good idea to fit the floor tiles making use of waterproof or waterproof sticky and also cement.
How to Install a Freestanding Bathtub?
Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.
This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.
Slope
Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.
Placement
A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.
According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.
Clean the bathroom floor
After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.
Steps to Install a Freestanding Bathtub:
STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.
STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.
STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.
STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.
STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.
STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.
Tips to Maintain a Freestanding Bathtub:
Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter. Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches. Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains. Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris. Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run. If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.

I am just very inquisitive about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I really hope you enjoyed the new article. Are you aware of another person who is sincerely interested in the subject? Be sure share it. We love reading our article about Tools You Need to Install a New Bathtub .
Get it sorted! Report this page